• Metric T Slot Aluminum Profiles

1. T Slot Vs V Slot Wins
2. T Slot Vs V Slot Poker
3. Building With Aluminum Extrusion
4. V Slot Aluminum Extrusions
5. T Slot Vs V Slot Car Racing

• Connectors

Throat dimensions are basic. When slots are intended to be used for holding only, tolerances can be 0.0 + 0.010 inch or H12 Metric (ISO/R286); when intended for location, tolerance can be 0.0 + 0.001 inch or H8 Metric. Corners of T-Slots may be square or may be rounded or broken to the indicated maximum dimensions at the manufacturer's. However, because T-slot aluminum profiles are assembled with hand tools, you can just take out the damaged piece and replace it with a new one. Unlike steel which the damaged piece will need to be cut out, and then you need to re-weld, clean, and re-paint the new piece.

• Fasteners

Here you can order pre-cut V-Slot to your desired length! 6 Item(s) Sort By. Set Descending Direction.

• Accessories

• Frame to Floor

• Panel Accessories

T Slot Vs V Slot Wins

• CarboSix Carbon Fiber

A new project requirement has come up and you need to figure out how to fabricate some framing. However, you don't know whether to choose between T-Slot Aluminum or welded steel, but, what if I told you, that by using extruded aluminum, you can reduce fabrication time and cost without compromising strength or quality? Intrigued? Well here are some of the benefits that T-slotted aluminum has over welded steel.

Cost Effective and Reduced Fabrication Time

Aluminum extrusions costs less than welding steel. While aluminum might cost more in raw materials, there is less overhead overall. Unlike steel which in addition to the costs for the materials, it also has higher labor costs associated with it. A steel frame will need to be welded, then the holes will need to be drilled and tapped (for mounting any panels or fastening additional components), along with cleaning, prepping, priming, and painting the frame. Quite a lot of work for just a simple frame. Aluminum extrusions are modular and with it being T-slotted there is never any need to drill or tap holes for other parts. Plus, you don't have to paint it because it already has a clear anodized protective finish.

Flexibility

Aluminum profiles can save money by giving engineers the flexibility after the initial design of a project has been completed. With steel, you need to make sure you're as close to 100% accurate as you can get before you begin cutting, drilling, and welding. With aluminum, you don't have to go into such minute detail so early in the project. Need to add a control panel or an electrical bracket? All you have to do is install a few additional cross beams to mount it. You can worry about the exact location later. With Framing Tech's modular aluminum profile system, you can attach components any time at any location.

Modular

You've just finished fabricating a steel frame and the customer wants to make a change and add another horizontal cross-member for additional equipment mounting. With a welded frame you would get the hack-saw or cutting/plasma torch out and make a mess of your freshly painted steel frame. Not only does this drive up the cost but now you have to go through the whole tedious process of cutting, re-welding, cleaning, and painting the new piece onto the project. Now, lets substitute that with T-slotted extruded aluminum. All the pieces arrive pre-cut or fully assembled, and all you need to do is add to it. Customer wants to modify the project? No problem! Because of the modular design of T-slotted aluminum, all you have to do is order the additional piece along with the hardware, attach it by tightening a few connectors and you're ready to go. Lower Labor Costs and therefore lower overhead costs equals a better bottom line as well as faster project completion time.

The Aluminum Extrusion Strength Question

Even though aluminum extrusion profiles have grown in popularity in the last few years, engineers who haven't worked with aluminum profiles question its structural integrity. When engineers think of aluminum, they think, lightweight and then, more often than not they'll over-design with these materials because to them it doesn't look quite right. But, contrary to this belief, extruded aluminum is strong enough to handle most manufacturing and automation assembly applications. Of course, both steel and aluminum structures will bend if they're hit hard enough or are subject to over-stressed loading. However, because T-slot aluminum profiles are assembled with hand tools, you can just take out the damaged piece and replace it with a new one. Unlike steel which the damaged piece will need to be cut out, and then you need to re-weld, clean, and re-paint the new piece. Framing Tech can recommend the correct profile series based on load (support) requirements using our many years of application engineering experience along with SolidWorks 2015 load calculations. Just ask & we’d be glad to “run the numbers” for your application.

Just to give an example of how you can save with an extruded aluminum profile, here's a side-by-side cost comparison with T-slotted aluminum vs. welded steel of a 24x24x18 frame:

Aluminum vs. Steel

T-Slot / V-Slot

T-Slot has been around for many years. It has matured to a solid building system using in industry and by hobby engineers to build everything from machine enclosures to CNC machines, 3D printers and robots! It is strong enough to withstand many industrial stresses and modular enough allow for universal designs.

The T-slot system consists of extruded aluminum of various sizes with a “T” shaped slot on one or more of its sides. The shapes, sizes and designs may be different, but the “T” slot is common to all. The “T” slot allows of a variety of hardware to be connected to the extrusion so that complex structures can be constructed.

Types of T-Slot

There are many types of T-Slot available on the market. Some of the most common for small scale engineering include:

T Slot Vs V Slot Poker

Building With Aluminum Extrusion

• V-Slot
• MakerBeam
• OpenBeam
• MicoRax

V Slot Aluminum Extrusions

As show above, these 4 type range from 10mm to 20mm square profile. Each profile has its unique features, but all share the “T” slot function.

The profiles are not limited to square. V-slot, for example, comes in 4 sizes 20x80mm, 20x60mm, 20x40mm and 20x20mm :

Some manufactures produce larger square and other shaped profiles:

T Slot Vs V Slot Car Racing

MakerBeam can fit a screw into its T-slot:

MicroRax is small, light and uses t-nuts and screws:

OpenBeam can fit a standard nut into its t-slot:

V-Slot uses t-nuts and is different from the other profiles because has “V” grooves that fit special “V” wheels and allow for easy linear motion:

Above are four different approaches to T-slot, there are in fact many more.